EVO™ Series Accessories

EVO™ Series Accessories

Interface modules, dispenser interface module cables, and paper supplies.

Order Info


Module Selection Guide

Download the guide now.

EVO™ Module Selection Guide

 

EVO™ 600 and EVO™ 6000 Interface Modules

The EVO™ 600 and EVO™ 6000 come standard witha Power Supply Module and a Controller Module. Additional interface modules can be installed. Interface modules ordered with an EVO™ will be installed at the factory (FMP-/TS-). If you would like them to not be installed, please order the spare/replacement version of the module (FMSP-/TSSP-).

  • EVO™ 600: 6 total modules can be installed with a maximum of 4 intrinsically safe modules.
  • EVO™ 6000: 11 total modules can be installed with a maximum of 9 intrinsically safe modules.

The following guidelines must be followed:

  • AC Input, 2-Wire Sensor, and 3-Wire Sensor Modules
    - No limits
  • Relay + 10A Relay + Input Output Modules
    - Must be ≤ 4
  • UDP 24V
    - Must be ≤ 4
  • 4-20 mA + RS-485
    - Depends on how many UDP 24V modules are being used.
Total UDP 24V Modules Allowable 4-20 mA + RS-485 Modules
0 or 1 4
2 3
3 1
4 0

NOTE: If your application requires exceeding the module guidelines, please contact your sales representative.

Pre-Installed Intrinsically Safe Modules

Model Description
TS-PRB Probe Module, 12 inputs, Compatible with TSP-LL2-XXX, TSP-LL2-XXX-I, FMP-LL3-XXX, and FMP-LL3-XXX-I probes; TSP-DMS-XX and FMP-XXX-U sensors; and TS-VFM vapor flow meters
TS-3WSNS 3-Wire Sensor Module, 8 inputs, Compatible with FMP-DDS*, FMP-DIS*, FMP-DTS*, FMP-EIS*, FMP-HIS*, FMP-HIS-XL*, FMP-UHS*, FMP-ULS*, TSP-DVS, TSP-HLS-XX, and TSP-HLS-XX/SS sensors
TS-2WSNS 2-Wire Sensor Module, 12 inputs, Compatible with FMP-HFS2, FMP-UHS*, FMP-ULS*, TSP-HLS-XX, and TSP-HLS-XX/SS sensors
TS-420IB 4-20 mA Module, 8 inputs, Intrinsically Safe, Compatible with FMP-LSU500 and TS-LSU500 transducers and FMP-TEM, TS-VPS, and TS-SCCM sensors
  • -U sensors are not supported on the 2-wire or 3-wire sensor module.

Pre-Installed Non-Intrinsically Safe Modules

Model Description
TS-10ARLY Pre-Installed 10 Amp Relay Module | 6 outputs | 10 Amp | Compatible with high power dispenser shutdown control functions
TS-420EXP 4-20 mA Module, 8 inputs, Explosion-Proof, Compatible with TS-LSU500E transducers
TS-ACI Pre-Installed AC Input Module | 12 inputs | Compatible with dispenser hook signal monitoring functions
TS-IO Pre-Installed Input Output Module | 4 4-20 mA outputs | 8 3-240 VAC/DC inputs | Compatible with remote monitoring control and building monitoring system interfacing functions
TS-RLY Relay Module, 8 outputs, 2 Amp, Compatible with submersible pump control, water separator control, secondary monitoring control, and overfill alarm control functions
  • TS-RLY Module is not required for STP control when utilizing turbine pump interface (TPI) communications. The TS-420EXP module requires Controller Module software version 9.5 or greater Do not include Power Supply and Controller Module when calculating total modules allowed.

Dispenser Interface Module Cables

Model Description
TSP-BDCBL Bennett® 515 only cable
TSP-GDCBL Gilbarco® cable
TSP-GSDCBL Gilbarco® G-Site™ cable
TSP-WDCBL Wayne™ cable

Printer Paper Supplies

Model Description
TS-TP2 One box of 5 rolls of thermal printer paper for fuel management system and Tank Sentinel® consoles
TS-TP2C One case of 20 boxes of 5 rolls of thermal printer paper for fuel management system and Tank Sentinel® consoles

Legacy ATG Paper Supplies

Model Description
TS-INKRB TS-550 and TS-5000 ink ribbon
TS-TP5000 TS-550 and TS-5000 impact printer paper
TS-TP5000C 12 rolls of impact printer paper
  • T5 Series consoles shipped after 8/2010 have thermal printers.

Network Expansion Box

Model Description
FMP-NEB Network Expansion Box with 8 Ethernet inputs (EVO™ 600/6000 only)